Login or Sign Up. Water heater install with copper lines who is right? Posts Latest Activity. Page of 1. Filtered by:.
Have a butane lighter lit ,and at the hood water heater vent cavity. It's easy to overlook this requirement, but it's a vital one. No need to use these particular brands, they are just the first ones I found. I don't use brass on our boat. My confusion is with the Brass water heater connetions nipples and dialectric unions. Share: Facebook Twitter Email Link. It's common to omit this overflow tube or to install it improperly, and this exposes everyone in the room to injury in the event that the valve opens.
Brass water heater connetions. Explore the different types of pipe fitting connections and when each type is used
EZ Check for back draft. If you want to use shark bite, then put a copper x male sharkbite on and connect the nut by nut. This was done by a plumber when the house was built. Brass Fittings for Water Heater okay? Home Guides Home Home Improvement.
Download it here.
- Fittings fit, it's true.
- Log in or Sign up.
- Questions and discussions about toilets, sinks, faucets, drainage, venting, water heating, showers, pumps, water quality, and other exclusively PLUMBING related issues.
When you buy a new water heater, it's important to gauge your hot water needs accurately so that you get a heater large enough to supply them. Having done that, you can install the heater yourself, but homeowners who do sometimes make mistakes, and some of them can cause damage to the heater or even personal injury. Being aware of the common mistakes can help you avoid them and ensure Brass water heater connetions safe and efficient installation.
When connecting your new water heater to the water pipes, you'll probably have to make solder connections, and a common mistake is to do this too close to the tank. Bang that babe heat it takes to melt solder can also melt plastic fittings inside the tank. A better way to make the connections is to unscrew the nipples from the top of the tank and take them to a work bench to solder on the needed pipe and fittings.
Leave only one connection to solder after you replace the nipples, and make it as far from the tank as possible. You don't have to pay special attention to the water connections if your tank has brass or copper connectors, and the pipes in your house are copper. If either the tank nipples or the pipes are galvanized steel, however, and you are connecting them Brass water heater connetions copper, you must use wager fitting called a dielectric union to make the connection.
It keeps the pipes from actually touching each other because, when they do, they create a corrosive electric charge that deteriorates the pipes and causes leaks. Both the hot and cold water pipes must have this fitting -- it's a code requirement. This valve can open unexpectedly and spray scalding water, so it must be connected to a watertight pipe that extends to within 6 inches of the floor. It's common to omit this overflow tube or to install it improperly, and this exposes everyone in the room to injury in the event that the valve opens.
If the valve is on top of the tank, the overflow tube should extend along the top and down the side of the tank to the floor. If you live in a seismic zone, the tank must be securely strapped to the framing Bgass prevent it from tipping in the event of an earthquake. It's easy to overlook this requirement, but it's a vital one. Before beater up your tank, whether it's hezter electric or gas model, it must be full of water. Homeowners who forget this connetjons end up having to replace the electric heating elements -- which burn out -- or the tank itself, which can crack when heated by a gas burner.
Water should be running in a steady stream from the hot water faucets before you turn on the heater. Chris Nice pregnant pictures has a bachelor's degree in physics and a master's degree in humanities.
Besides having an abiding interest in popular science, Deziel has been active in the building and home design trades since As a landscape builder, he helped establish two gardening companies.
Skip to main content. Home Guides Home Home Improvement. About the Author Chris Deziel has a bachelor's degree in physics and a master's degree in humanities. Deziel, Chris. Home Guides SF Gate. Note: Depending on which text editor you're pasting into, you might have to add the italics to the site name. Customer Connetinos Newsroom Contacts.
Flare connections are used when water pressure is high, or for gas distribution: applications with higher pressures than a compression fitting could handle. When used with soft copper, a special tool (called a flaring tool) is used to flare the tubing, modifying its shape to facilitate a . Nov 16, · BrassCraft 3/4 in. Fip x 3/4 in. Fip x 12 in. Polymer braided water heater connector ( in. I.D.), also known as speedi plumb plus connector, combine advanced corrosion technologies with state-of-the-art manufacturing to provide the most flexible, corrosion resistant water heater connector available on the market today/5(5). Genuine BrassCraft replacement water heater connector washer. Use with ProCoat coated corrugated stainless steel and Copper-Flex corrugated copper water heater connector with an internal dielectric sleeve. All 3/4 in. FIP water heater connections require a washer to seal the connection. Genuine BrassCraft replacement part5/5(1).
Brass water heater connetions. Water heater install with copper lines who is right?
The plastic liner wraps partially over each end. The clamps couldn't be tightened enough and the fitting would deform. You don't have to pay special attention to the water connections if your tank has brass or copper connectors, and the pipes in your house are copper. The previous plumbing used plastic fittings to reinforced pvc. I am afraid the warranty will be void if I do not use the plasic lined nipples. Don't use tefelon tape on any of the threads, just a little pipe compound, to help it screw on just a little farther. The female side of the union has very deep threads and the plastic inside the nipple will in no way seat against the union. I'm buying a new water heater, and quite frankly the series of connections and valves are mind boggling. Hints the Term. Page of 1. Thread starter Dreaming Start date Apr 23, Is there any reason to not put a valve on the hot too? Skip to main content. I found that the plastic fitting on the hot water side allowed the hose to keep sliding off.